This tester is used to conduct dynamic test ( launch or impact method ) upon the headrest assembly. The impact angle can be different from the angel of headrest.

This tester is used to measure the load value of each point on a seat and get an average value, in order to make sure the seat can has even load on each point so as to achieve comfortable sitting. Durability test for the seat sponge of car seats.

This tester is used to test the strength and deformation of welding points for the frame of car seats before or after forming.

This tester is used to test various items upon formed car seats in order to ensure the lifetime of car seats. Those tests include strength test of backrest of both sides, durability test of backrest, strength test of seat and durability test of seat.

This tester is used to test various items upon formed car seats in order to ensure the lifetime of car seats. Those tests include strength test of backrest of both sides, durability test of backrest, strength test of seat and durability test of seat.
The testing method is different from the one of HT-2123. If both test methods are different from your requirements, further discussion is welcome.

This tester adopts mechanical movement to measure the repetitious rebound resilience and durability of the seat sponge material of car seats.

Every time we sit on the car chair, we move the seat along the slide to adjust the space for legs. This tester is for testing the durability of car seat. After finishing the preset test cycles, observe how the seat slide is worn out in order to judge its quality.

When sitting in cars, we have often to adjust the angel of seat-back in order to have the most comfortable sitting. This machine is used to conduct durability test for the reclining switch of car seats. After finishing the preset testing cycles, observe the test sample and see how it get worn out , so as to judge its quality.

The machine is used for testing the seat strength at different part of seat, specially the extended seat for van or pickups. It is available to individually control the each oil pressure vat action, set up each axes loading and test condition. But set up at the beginning of loading, and can each test axes at the beginning of loading arrive time, execute test loading action again.

This machine is used to measure the durability strength of seat frame. While testing, apply a certain force forwards or backwards upon the sample. Different test methods can be preset to perform the test. After that, observe the sample t judge its quality which is a good reference for product improvements.

This machine is used to measure the durability of car seats, under continuously horizontal, vertical or a given degree, and a given load, for fatigue durability test.

This tester is used to measure the durability character of head-rest of car seats. This machine can conduct the test of vertical movement of head-rest assembly, or push the headrest back and forth, in order to evaluate its quality.

This tester is used to conduct static impact test upon head-rest of car seats. While testing, apply a force torque upon the seat back, and then apply another force upon head-rest and then measure its displacement.

This machine is used to measure the rebounded height of seat foam after undergoing a certain force of impact.

A tester that can be applied to conduct the abrasion test of vehicle’s lamp specified by the CNS 1351, SAE and for the vehicle lamps to be exported.

Suitable to bike’s parts and materials, applied to the tests of bike product’s tensile, compression & torsion strength of wide application scope.
This instrument’s fabrication has passed the ISO-9000 international quality certification, compliant with the ISO 7500 / 1 EN, 1002-2, BS 1610, DIN 5122, ASTM E4, JIS B7721 / B 7733, CNS 9471 / 9470 & JJG 475-88 test standards to material tester.
And we also can follow the international bike’s standards listed below to use the respective bike jig/fixture module:
*ISO
*BS / DIN / NF (U.K./Germany/France)
*CPSC / CSA (USA/Canada)
*JIS / JBMS / BA (Japan)
*AS / NES (Australia/New Zealand)
*GB / QB / CNS (Mainland/Taiwan

JIS D4411, CNS 2586, D2002
Designed for testing the frictional performance of automotive brake linings and clutch facings as stipulated in JIS-D4411, CNS-2586 D2002 thus contributing to the improvement of quality. This tester was created under the guidance of the Machinery Research Division, the Agency of Industrial Science and Technology. Since introduced to the market, this tester has been received quite well and employed extensively in various fields and industries such as the manufacturing of linings, clutches, and plastics.

This machine is used to test the fire resistance of organic materials like various wire and cables, PC boards, IC insulating sheath...etc. While testing, put sample at the tip of the flame that won't swing owing to the breeze. Let the flame burn for 15 seconds and out for another 15 seconds. Repeat another four times, ( Total Five Times ) and check the burning situation of the sample. Type A is of automatic model that is available to freely set the burning time, out time, repeat time and even available to be operated automatically.

Bearing oil seal tester is designed for the testing of various load of springs, bearings, under the condition of continuous running, set different temperature and revolving speed to test durability and tightness of products.

The design and test method is as per the norm of CNS 4119, and refer to JIS4604-1988, FMVSS No. 207, ECE No. 16-04, ADR 4100...etc. This applies pullout and refractive force on the retractor of the webbing of car seat in order to inspect its quality.

This machine is to test the webbing on two rhombohedra corners of a hexagonal rod, in order to determine the quality of the webbings.

This tester is used to test the durability of retractor by making webbing pull out and retract back repeatedly. Pull out all webbing length and then apply the tensile force of 90N ( 9kgf ). Then release it to retract back all the webbing and which is regarded as one cycle. Apply this test for 2,500 cycles by the speed of 30cycles per minute, and check test status.

This tester is used for measuring the maximum torque force for the materials of metal, polymer, the products of golf shaft, tennis ( badminton ) racket, and available to record the test graph in order to analyze the torque resistance of material, and so as to be a good reference for product improvement.

This tester can generate an acceleration at a selectable certain level within 50 mili-seconds in order to test if the retractor is of good quality.

This tester is to test the characteristics of fatigue resistance of belt under a dusty circumstance by repeatedly pulling out and retracted back. After test procedures ( Described Below ) , manually pull out and retract back the webbing for 25 cycles to check if the retractor is still functional.

This tester is for testing the damping strength of shock absorbers. Available to test the shock absorbers for car and motorcycle and even truck, but only for rear shock absorbers for bicycle. Normally the specifications are different depending on different test requirements. Hereunder are the standard specifications for this model.

CNS-3973
This tester is used to determine the durability of buckle for its front-press or lateral-press buckles. After testing for 5000 cycles of test, inspect the buckle if it is injured or worn.

Among the seats for motorcycle or automobile, the quality of the compounded foam inside matters so much if the passenger is comfortable sitting on it.
This is to press first 75 % of the sample thickness, release and then press 25% still for 20 seconds and then record its force. That would be the hardness of the compounded foam.

Most transmission or steeling parts, generators, air conditioner, igniting motor, which may be invaded by muddy water sprayed from the bottom panel, and so cause bad effect of transmission, defective anti-dust cover and worn out of ball joints. This tester can help to test these parts with related functions and so to get the best effect of anti-dust and anti-water for your products.

Ball joints undergo multi-functional loads while an automobile is being driven on the road, especially when the road surface is bumpy. Therefore, the durability of ball joints becomes an important issue for the ball joint producers and carmakers. This tester sets a strict level of testing conditions; the test results of this tester are highly essential information for product improvement and development.

■ The output axle of exciter is light in weight & high stiffness ; the axial resonant frequency is above 2000 Hz.
■ On-line to computer, data inputted is stored right away; precise control can be reached.
■ Can monitor the control conditions ( Vibration frequency, amplitude, velocity and acceleration ) of operation on display.
■ Apply low-resistance & high-performance design to elevate machine's efficiency and reduce the test cost.
■ Excellent magnetic-flux-leakage-blocking effect that can prevent from disturbing products under test.
■ Apply PC based controller, 15" display, easy to operate.
■ PC based display can display the control curve.
■ Can print out test report from colored screen; and have infinite storage space.
■ Provide dynamic analysis diagram to jigs and fixtures to ensure test's reliability.

HT-9363-1
1. HT-9363-EM-600F2k-40N120.
2. Controller : HT-9363-EM1 sine wave.
3. Auxiliary table : VF-600-H.
4. Table size:600 x 600 SQmm.

HT-9363-2
1. HT-9363-EM-300F2k-30N80.
2. Controller : HT-363-VC1 Random spectrum.
3. Combined with the PC board production line fixture to E.S.S
.
HT-9363-3
1. Controller : Sine/Random with PC base
2. System protect : HT-9363-PT3.
3. Cooling system : Force air cooling.
4. Base isolating: pneumatic cushion base.

HT-9363-4
1. Mini shaker for Calibration accelerometer use.