CNS2054 3479 JIS-L1018, P8112, ASTM-D2210, TAPPI T403ts-63
This tester is used to determine the bursting strength of paper and corrugated board. It is an essential piece of equipment for quality control.

CNS2054 3479 JIS-L1018, P8112, ASTM-D2210, TAPPI T403ts-63
This tester is used to determine the bursting strength of paper and corrugated board. It is an essential piece of equipment for quality control.

CNS2054 3479 JIS-L1018, P8112, ASTM-D2210, TAPPI T403ts-63

CNS2054 3479 JIS-L1004, L1018, L1031, K6328, P8131, P8112, ASTM-D2210, TAPPI T403ts-63

CNS2054 3479 JIS-L1004, L1018, L1031, K6328, P8131, P8112, ASTM-D2210, TAPPI T403ts-63 
This tester is used to determine the bursting strength of paper and corrugated board. It is an essential piece of equipment for quality control.

JIS-K630, K-7212, ASTM D-2436, E-145,
JTTC SPEC.-151 CNS 3556
The oven is used for degradation study of plastics & rubber when subjected to heat in a rotational condition for a specified time. One day test at 70°Cis theoretically equivalent to a six-month usage in normal environmental condition. The machine is equipped with a motor-driven rotary plate. Hot air circulation will ensure even temperature distribution.

This machine is used for conducting the vibration test of mechanical, electronics, electrical parts, telecommunications, computer and auto parts. This application is available for checking the samples for resisting the effect while under transportation or durability testing.

This machine is used for conducting the vibration test of mechanical, electronics, electrical parts, telecommunications, computer and auto parts. This application is available for checking the samples for resisting the effect while under transportation or durability testing.

This tester is made in accordance with C.I.E. and certified the minimum interferance of the ultra light.

CNS-2999
In the transportation process, packed products might be unavoidably dropped or accidentally impacted with hard substance. To prevent further damages in advance, this tester is designed to test and find out the ultimate solution for the package products with a purpose to reduce loss during transportation.

During the transportation process, packed products unavoidably being dropped or accidentally impacted with hard substance. To prevent further damages in advance, this tester is designed to test and find out the ultimate solution for the package products with a purpose to reduce loss during transportation. Compared with our previous version of single arm design, this twin-arm type is easier and more convenient to use.

This tester measures the adhesiveness of adhered materials such as copper foil, aluminum foil, tin foil or even paper labels. The lower layer is gripped firmly, while the upper layer is pulled laterally 90° from vertical. The force is read through a push-pull gauge.

Recently, for the convenience of most operators, we modify this machine to be speed adjustable, so that the operator could use different test speed in order to test his samples.

Micro-computer compress tester is applied to test the packing carton box or the container like commodities how heavy load it can afford.
To determine the crack or collapse arose due to a positive, consistent pressure adding to the testing particles.

TAPPI-T414, JIS P-8116, CNS-B53
To test tearing strength of fabric, paper, PVC material etc. Specimen are being slightly splitted. One side is firmly gripped and the other is being gripped and moved forward to effect tearing action scale pointer indicates tearing strength.

Owing to the transportation needs, stacks of the carton boxes being piled upward, the endurance of such heavy load is determined by the composition of the paper board. To tell the difference of the burden strength, Micro-computer Ring Crush Tester is inevitable, useful and helpful.

To cut the paper board which is suitable for testing purposes ; otherwise irregular or misuse of the improper paper board may result in an incorrect test. There are two models : The parallel cutter and the corner cutter.

To cut the paper board which is suitable for testing purposes ; otherwise irregular or misuse of the improper paper board may result in an incorrect test. There are two models : The parallel cutter and the corner cutter.

This grip is used for chucking the upper and lower ends of sample paper boards to make sure specimen stands vertically, thereby facilitating the vertical compression testing of the paper boards. The grip should be used together with ring crush tester.

This tester is for testing the transverse compression strength of paper tubes, bobbins, paper cans, composite cans, paper cones and so on. It can also be used for testing taper tubes.

■ The output axle of exciter is light in weight & high stiffness ; the axial resonant frequency is above 2000 Hz.
■ On-line to computer, data inputted is stored right away; precise control can be reached.
■ Can monitor the control conditions ( Vibration frequency, amplitude, velocity and acceleration ) of operation on display.
■ Apply low-resistance & high-performance design to elevate machine's efficiency and reduce the test cost.
■ Excellent magnetic-flux-leakage-blocking effect that can prevent from disturbing products under test.
■ Apply PC based controller, 15" display, easy to operate.
■ PC based display can display the control curve.
■ Can print out test report from colored screen; and have infinite storage space.
■ Provide dynamic analysis diagram to jigs and fixtures to ensure test's reliability.

HT-9363-1
1. HT-9363-EM-600F2k-40N120.
2. Controller : HT-9363-EM1 sine wave.
3. Auxiliary table : VF-600-H.
4. Table size:600 x 600 SQmm.

HT-9363-2
1. HT-9363-EM-300F2k-30N80.
2. Controller : HT-363-VC1 Random spectrum.
3. Combined with the PC board production line fixture to E.S.S
.
HT-9363-3
1. Controller : Sine/Random with PC base
2. System protect : HT-9363-PT3.
3. Cooling system : Force air cooling.
4. Base isolating: pneumatic cushion base.

HT-9363-4
1. Mini shaker for Calibration accelerometer use.

This cutter is round in shape and is used for cutting corrugated paper boards bearing a plane surface pressure of 38.5 x 38.5c., thereby facilitating the testing of pressure resistance of the boards. It should be used together with ring crush tester. Size of sample : ( a ) 38.5 sq.cm ( b ) 100 sq.cm

This tester is applied to tear away the corrugated fiber boards with pins inserting into the flute of the fiber boards to test the adhesive strength between the flute and flat paper board of corrugated board.

CNS 3687, JIS P8137
In order to test the corrugated fiberboard under the precipitate conditions. Rain occasionally falls on paper when left outdoors. If the water is not immediately absorbed, water tracks are left behind. As a result standard test outcomes layout as 8 categories : R0,R2,R4,.....R10.

Dropping 50 ~ 100ml. of distilled water directly on the specimen, after a certain period of time, the water is absorbed by the paper. This is a way to test a paper's texture and absorption rate.

CNS 11484, JIS P8134, TAPPI T803
In combination with the use of bursting strength tester, Puncture Tester turns to be an indispensable instrument for inspecting the structural strength of the finished corrugated paper board. In fact, Puncture Tester is a dynamic way to test the quality of the paper board whereas the bursting strength tester is a static method. Both of them are interrelated and neither of them can be neglected.
It is suitable for testing general paper boards, corrugated paper boards, plywood board, plastic boards and fiber boards. The punch head is a triangle pyramid to break the specimen

.

Folding endurance tester is a typical way of fatigue testing paper. Repeatedly folding the 15mm width specimen to 135 degrees ; the counter automatically records the folding frequency.

For examining the durability of wheelchairs in order to test the overall construction, or to understand the weakness of the wheelchair as an important reference point for further improvement and development.

For examining the durability of wheelchairs in order to test the overall construction, or to understand the weakness of the wheelchair as an important reference point for further improvement and development.

The die cutter is used to cut a specimen into a long narrow stripe, and then place the stripe specimen into a round feature jig ( or ring crush tester ) for the operation of testing procedures.